1999 Ford Ranger 3.0 Head Bolt Torque

10a Apply light coating of grease to surface where bolt meets Head. Recommended you replicate on all bolts - torque symmetry.

1998 Ford Ranger 3 0 Cylinder Head Torque Specs And Intake Torque Specs With Tightening Bolt Order

Fastener Type Torque Spec Main cap bolts 60-70 ft-lbs Outer main cap bolts 35-40 ft-lbs.

1999 ford ranger 3.0 head bolt torque. For 289 HP Boss 302 Cylinder head bolts 65-72 ft-lbs. I Have A Haynes Manual Wich Gives The Torque Values But It Doesnt Specify If. Torque the new cylinder head bolts in stages as follows.

Fastener Type Torque Spec Main cap bolts 60-70 ft-lbs Outer main cap bolts 35-40 ft-lbs. Chilton and Alldata both give 59 fp back off 1 turn 37 fp 68 fp for both 1998 and 1999. The illustration above shows the intake manifold bolt tightening sequence to avoid damage to the intake manifold gasket or vacuum leaks.

10 Head Bolt Installation. If your foot-pound torque wrench does not adjust to 8 foot-pounds torque to 96 inch-pounds with an inch-pound wrench. Connecting rod bolts 40-45 ft-lbs.

14 FtLbs STE P 2. 1999 Ford Ranger Head gasket replacement. Does any one know if they have to be tightened in a specific order.

10b If a bolt passes through coolant passage apply gasket sealer. 10b If a bolt passes through coolant passage apply gasket sealer. Tighten all bolts in sequence an additional 90 degrees recheck final torque in sequence CAUTION engine uses Torque To Yield head bolts TTY thatpermanently stretch during the initial installationNew head.

Avoid drips or runs smooth light coating. ALL Bolts 180deg turn Read full answer. When installing the intake air plenum be sure to catch the four center bolts and the two side bolts stiffener brackets before tightening The center bolts should be torqued to 250 inch pounds The fuel rail bolts should be torqued to 100 inch pounds.

Rocker arms 17-23 ft-lbs. Rocker arms 17-23 ft-lbs. Torque each fulcrum bolt to 8 foot-pounds.

Intake manifold bolts 23-25 ft-lbs Oil pump bolt 23-28 ft-lbs. Torque to 250 in-lbs or 2083 ft-lbs Connecting road bearing cap nuts. Torque rear main bearing cap bolts to 88 FtLbs Step 3.

Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 8-10 ft-lbs. Flywheel flex-plate bolts 75-85 ft-lbs.

1996 1997 1998 1999 30L OHV Ford Taurus And Mercury Sable. Torque to 20 ft-lbs then rotate an additional 14 turn. While the head bolts are being torqued to the specified value the technician can use the TRQ-1 tool to accurately measure the degrees of additional rotation required.

I have a haynes manual wich gives the torque values but it doesnt specify if there is an order in wich they have to be tightened. Recommended you replicate on all bolts torque symmetry. SHORT Bolts Loosen 3 Turns - re-torque to 19FtLbs STEP 5.

Cylinder Head Bolt Torque Specifications. With T-T-Y head bolts the Torque-To-Angle Indicator Part Number TRQ-1 should be used in conjunction with a torque wrench to achieve proper bolt loading. Intake Manifold Bolt Torque Specifications.

36 FtLbs STEP 4. Harmonic damper bolts 70-90 ft-lbs. Harmonic damper bolts 70-90 ft-lbs.

Loosen the bolts one full turn. Torque brace bolts to 40 FtLbs Connecting rod torque. 1999 Ford Ranger Head Bolt Torqueing I Am Changing The Head Gasket On M 99 Ford Ranger 30 V6.

The electric fuel pump is located inside the fuel tank. LONG Bolts Loosen 3 Turns - re-torque to 33FtLbs STEP 4. Torque bolts to 91 FtLbs with the exception of the rear main bearing cap Step 2.

Discussion in General Discussion started by kjohn2007 Jan 11 2012. Alldata also on one page only one section only for 1999 says these are TTY bolts and gives 37 fp back off 1 turn 22 fp 90 degrees 90 degrees In July 98 they changes to TTYs right. Install the intake manifold gaskets without any type of sealer.

Cam thrust plate bolts 8-10 ft-lbs. For 289 HP Boss 302 Cylinder head bolts 65-72 ft-lbs. Torque to 20 ft-lbs then rotate an additional 14 turn Main bearing cap cross bolts.

29 FtLbs STEP 3. The electronic fuel injection system on the 1996-1999 30L Ford Taurus Mercury Sable is the EEC-V. Cylinder Head Bolt Torque Specifications VIN 1 2 y U.

Pressure plate bolts 35 ft-lbs. Torque these bolts in a few small increments until they have reached 250 inch pounds of torque. 1999 Ranger 30 liter head bolt torque.

Intake manifold bolts 23-25 ft-lbs Oil pump bolt 23-28 ft-lbs. I am changing the head gasket on m 99 ford ranger 30 v6. 10c If no bolts pass through coolant apply light coating of oil.

Pressure plate bolts 35 ft-lbs. Flywheel flex-plate bolts 75-85 ft-lbs. Connecting rod bolts 40-45 ft-lbs.

10a Apply light coating of grease to surface where bolt meets Head. Inner main bearing cap bolts. 10c If no bolts pass through coolant apply light coating of oil.

But neither of these sources makes note of that. Cam bolts 40-45 ft-lbs. Torque to 15 ft-lbs then rotate an additional 14 turn Outer main windage tray bearing cap bolts.

The EEC-V fuel injection computer has 104 terminal. 10 Head Bolt Installation.

1998 Ford Ranger 3 0 Cylinder Head Torque Specs And Intake Torque Specs With Tightening Bolt Order